Sebo ET-H Owner's Manual download pdf (Page 6)

Page 6

Starting The Machine

- Figures 1 & 2

A. Before turning on your canister, make sure that the vacuum han-

dle is in its upright locked position (figure 1).

1. With the canister main power switch in the OFF position,

and the power control slider on the handle (#8, figure 2) in

the OFF position, pull the power cord out from the base of

the canister (see canister owner’s manual). The power

cord should be unwound from the cable reel at least two

thirds of its length.

2. Plug the polarized power cord into a 120 volt outlet

located near the floor.

3. Press the main power switch on the base of the canister

gently with your foot or hand to the ON position.

4. Slide the Power Control Slider (#8, figure 2) to the ON

position (the slider will “click” when it is pushed out of the

OFF position). It will then slide freely between 0 suction

and MAX suction. Set the slider to the suction desired. The

green power light situated on the top side of the power

head will illuminate.

Operating The Machine

- Figure 3

B. When the power head is switched on with the handle in the upright locked

position (see figure 1 above), the brush roller will not spin. To release the

power head from the upright locked position, gently place your foot on the

power head for leverage and lower the handle into the operating position (fig-

ure 3).The brush roller will then start spinning.The amber indicator light may

flicker for a few seconds when you lower the handle - this is normal.

The handle can be lowered to a horizontal position useful for vacuuming

under beds.

You may adjust the suction control with the power control slider as you vac-

uum different surfaces or when using the accessory tools. For optimal clean-

ing and brushing, operate the machine at the maximum suction power set-

ting and push the power head slowly over the carpet.

When the canister’s main power switch is in the ON position, you may turn

the power head off and on with the power control slider (#8, figure 2). To turn

the power head off using the power control slider, pull the slider to 0 suction,

then continue pulling the slider up until it “clicks” into the OFF position. The

green power head light will then shut off.

Always turn the power off on both the canister and the power head

when changing heads or unplugging the vacuum. Slide the power con-

trol slider on the power head to its OFF position, press the main power switch

on the base of the canister gently with your foot or hand, then unplug the

canister to completely shut down the power when changing heads or storing

the vacuum. Hold the plug while rewinding the cord onto the cord reel. Avoid

letting the plug whip while rewinding.

WARNING! The quality, condition, coating, texture, age and manufacturing technique of all floor surfaces vary.

Therefore, vacuums with rotating brushes, including your SEBO, may damage some floor coverings or surfaces. Some

types of high-gloss hardwood floors, cushion vinyl, berber carpets, long shag, and delicate or hand-woven carpets are par-

ticularly vulnerable to damage by rotating brushes. When possible, consult the materials supplied by your flooring manufac-

turer for information on proper upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible

with your floor, please test the vacuum cleaner on each type of flooring surface in a small inconspicuous area

to determine if any damage occurs. If damage occurs, stop using the vacuum cleaner immediately!

Operating Instructions

Figure 1

Figure 3

Figure 2

Switch Position -

#8, Figure 2

0 = Zero Suction

MAX = Maximum Suction

ON position - Slide the slider

down toward 0 suction till it

“clicks” out of position.

OFF position - Pull the slider

up to 0 suction then continue

pulling the slider up until it

“clicks” into the OFF position.

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Sebo ET-H Owner's Manual Page 6

Comments to this Manuals

Related products and manuals for Vacuum cleaners Sebo ET-H